Grandtec IP CAMERA II
no PCB foi ligado um conversor de nivel TTL MAX232 com a seguinte configuração:
Pin 1 = +3.35 V Pin 2 = TX Pin 3 = RX Pin 4 = Terra (0 V)
foi usado o minicom para aceder ao bootloader da board. 115200 8N1.
****************************************************
* IS90232Q IA Developnent Board *
* Designed by Integrated System Solution Corp. *
* Technology by ISSC Electronics *
* December 19, 2003 *
****************************************************
For help on the available commands type 'h'
Press ESC to enter debug mode ......
Cache disabed!
Processing image 1 ...
Processing image 2 ...
Processing image 3 ...
Processing image 4 ...
Processing image 5 ...
Processing image 6 ...
Unzip image 6 ...
Processing image 7 ...
Unzip image 7 ...
Executing image 7 ...
Linux version 2.4.20-uc0 (ipcam@AELab.ISSC) (gcc version 3.0) #483 Wed Apr 6 17:38:29 CST 2005
Processor: Winbond W90N740 revision 1
Architecture: W90N740
SDCONF0[0xFFF01008] = 0x000010E4
SDCONF1[0xFFF0100C] = 0x00000800
SDCONF0[0xFFF01008] = 0x000010E4
SDCONF1[0xFFF0100C] = 0x00000800
----------- end_mem = 0x01000000 -------------
On node 0 totalpages: 4096
zone(0): 0 pages.
zone(1): 4096 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/rom0
Calibrating delay loop... 39.83 BogoMIPS
Memory: 13MB = 13MB total
Memory: 11936KB available (914K code, 196K data, 44K init)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Winbond W90N740 Serial driver version 0.9 (2001-12-27) with no serial options enabled
ttyS00 at 0xfff80000 (irq = 6) is a W90N740
EEPROM driver initiate index = 0.
Blkmem copyright 1998,1999 D. Jeff Dionne
Blkmem copyright 1998 Kenneth Albanowski
Blkmem 1 disk images:
0: D00000-E02FFF [VIRTUAL D00000-E02FFF] (RO)
RAMDISK driver initialized: 16 RAM disks of 3072K size 1024 blocksize
loop: loaded (max 8 devices)
Error!! Read MAC Address for EEPROM..
Error!! Read MAC Address for EEPROM..
Regiter EMC 1 W90N740
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
Linux video capture interface: v1.00
WLAN macaddr = 0:1:0:3:0:5
usb.c: registered new driver hub
add a static ohci host controller device
: USB OHCI at membase 0xfff05000, IRQ 9
hc_alloc_ohci
usb-ohci.c: AMD756 erratum 4 workaround
hc_reset
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
pwc Philips PCA645/646 + PCVC675/680/690 + PCVC730/740/750 webcam module version 8.10 loaded.
pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
pwc the Creative WebCam 5, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
usb.c: registered new driver Philips webcam
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
NET4: Ethernet Bridge 008 for NET4.0
VFS: Mounted root (romfs filesystem) readonly.
Freeing init memory: 44K
Shell invoked to run file: /bin/init
Command:
Command: #mkfs o
Command: #mount -t minix /dev/rom1 /config
Command: #mount -t ramfs none /config
Command: mount -t ramfs none /swap
Command: mount -t proc none /proc
mount failed: Unknown error 16
Command: #mount -t ramfs none /etc/ConfigPage/Down
Command: #mount -t ramfs none /etc/Html/Jpeg
Command: httpd_ipcam&
[8]
Command: sh
Sash command shell (version 1.1.1)
/> Version: Build Apr 8 2005 19:40:34
Required flash size: 2112
new USB device :801e4a04-16cd60
hub.c: new USB device 1, assigned address 2
usb.c: USB device not accepting new address=2 (error=-110)
new USB device :801e4a04-16cd60
hub.c: new USB device 1, assigned address 3
usb.c: USB device not accepting new address=3 (error=-110)
setresetpid failed:8
EEPROM driver open
EEPROM driver close
[Begin WR_CONFIG_PARAM]
DDNS 0 [] [] [] []
Email 0 [] [] [] [] 5 -1874415119
ImageCfg 1 1 1 1 1 0 - 50 50 40 40
[End WR_CONFIG_PARAM]
EnableEmail=0
acMailSvr= [] sz=64
Initializing eth0...
Rdvalue 45e1
100MB - Full Duplex
eth0 is OPENED 2003/5/6 04:10�Ï�Â�Î�ç
Initialize eth0... over
SetMacAddress 0 00:13:FE:00:00:00
Rdvalue 45e1
100MB - Full Duplex
eth0 is OPENED 2003/5/6 04:10�Ï�Â�Î�ç
ISSC:--------- Manual Config-----------
Cannot del default route (3).
Time Server:161.53.40.3
.TIMEOUT
NTP error
Time Server:161.53.40.3
TIMEOUT
NTP error
Time Server:161.53.40.3
TIMEOUT
NTP error
__pthread_initial_thread_bos:bf0000
manage pid:10
Task 17 start.
Task 33 start.
Error opening video device.
init_cam retry 0
FTP:Enter Idle
email_main!!
EMAIL:Enter Idle
EMAIL:Enter Idle
Task 49 start.
ntp_main!!
NTP:Enter Working
NTP:IDLE
Task 65 start.
Task 81 start.
IPSET: ipsetc_main thread created.
IPSET: Device is: eth0
<6>httpd_ipcam uses obsolete (PF_INET,SOCK_PACKET)
Task 97 start.
EEPROM driver open
FF FF FF FF FF FF FF FF FF FF FF FF
EEPROM driver close
Start http server at: [/etc/ConfigPage]
fd = 6, port = 80
fd = 7, port = 2000
Flash size: 0x200000 bytes.
IPCam config information address: 0x1FF7C0
Error opening video device.
init_cam retry 1
Error opening video device.
init_cam retry 2
Error opening video device.
init_cam retry 3
Error opening video device.
init_cam retry 4
Error opening video device.
init_cam retry 5
Error opening video device.
init_cam retry 6
Error opening video device.
init_cam retry 7
Error opening video device.
init_cam retry 8
Error opening video device.
init_cam retry 9
Error Setup Video Input Format for Camera.
Error Setup Auto Exposure for Camera.
Error Setup Auto White Balance for Camera.
Error Setup Image Size for Camera.
Error Setup Image Framerate for Camera.
Error Setup Image Hue RGB for Camera.
Error Setup Image Quality for Camera.
Error Setup Image Hue Number for Camera.
Error Setup Image Brightness for Camera.
Error Setup Image Contrast for Camera.
Error Setup Image Saturation for Camera.
bootloader > ls Image: 0 name:BOOT INFO base:0x7F010000 size:0x00000040 exec:0x7F010000 -af Image: 7 name:linux.zip base:0x7F020000 size:0x00077FB4 exec:0x00008000 -acxz Image: 6 name:romfs.zip base:0x7F100000 size:0x000DC8BC exec:0x00D00000 -acz
